CRM Mitchell1, Author at Sheens Auto Care

2018 Subaru Forester
Mileage
78,983
Service Date
3/19/2025
Services Performed
WARRANTY
CHECK ALL FLUID LEVEL AND CONDITION
FRONT 32 REAR 30 (IN PSI UNIT) INSPECT TIRES AND ADJUST/INFLATE TIRE PRESSURE
BRAKE INSPECTION:FRONT ( 6 mm) REAR ( 8 mm) LINING REMAINING
PERFORM BATTERY TEST – PASSED
PERFORM MULTI INSPECTION
RESET REMINDER( ) REMINDER STICKER ( ) TEST DRIVE ( ) MILES
WHEEL LOCK (IF APPLICABLE) RESTORE ORIGINAL LOCATION.
TORQUE ALL LUG NUTS PER OEM SPEC (IF WHEELS REMOVED)
Check brake fluid for moisture and contamination. Inspect all hydraulic line and hoses. Inspect calipers and wheel cylinders. Inspect master cylinder and cap. Flush entire brake system including master cylinder, calipers, wheel cylinders until clean.
Inspect hoses and clamps. Do pressure test cooling system. Drain and fill engine, radiator, heater core section and fill with new coolant. Bleed coolant system per oe recommended procedure, check thermostat and elec. cooling fan operation. Perform drive cycle and test drive.
ALTERNATOR DRIVE BELT – Remove & Replace – 2.5L Eng – [Includes: Serpentine and V-Belt type Belt(s).]
TOP OFF WASHER FLUID.
Bobby H. gave our service a 5 star review on 3/19/2025
2023 Toyota RAV4
Mileage
16,752
Service Date
3/4/2025
Services Performed
BALL JOINT & DUST COVERS – INSPECT – [Check the suspension and steering linkage ball joins for looseness and damage. Check all dust covers for deterioration and damage. Replace any deteriorated or damaged parts.] BRAKE HOSES & LINES – INSPECT – [Visually inspect for proper installation. Check for chafing, cracks, deterioration and signs of leaking. Replace any deteriorated or damaged parts.] BRAKE SYSTEM – INSPECT – [Visually inspect brake linings/drums and brake pads/discs.] DRIVER'S FLOOR MAT – INSPECT – [Only use the driver's floor mat designed specifically for the model and model year of your vehicle. Always properly secure the driver's floor mat using the retaining hooks. Never install another floor mat on top of the existing driver's floor mat. Never install the driver's floor mat upside down.] DRIVESHAFT/PROPELLER SHAFT DUST BOOTS – INSPECT – Drive Shaft Boots – [Check the drive shaft boots and clamps for cracks, deterioration and damage. Replace any deteriorated or damaged parts and, if necessary, repack the grease.] ENGINE COOLING SYSTEM HOSES & CLAMPS – INSPECT EXHAUST PIPES & MOUNTS – INSPECT – [Visually inspect the exhaust pipes, muffler and hangers for cracks, deterioration and damage. Start the engine and listen carefully for any exhaust gas leakage. Tighten connections or replace parts as necessary.] FLUID LEVELS – INSPECT – [Inspect and adjust all fluid levels.] RADIATOR & CONDENSER – INSPECT – [Inspect for damage, debris, dirt, insects and signs of leakage.] STEERING GEAR/RACK – INSPECT – [Check for damage/leaks.] STEERING LINKAGE & BOOTS – INSPECT – [With the vehicle stopped, check for excessive freeplay in the steering wheel. Inspect the linkage for bending and damage and the dust boots for deterioration, cracks and damage. Replace any damaged parts.] TRANSFER CASE FLUID – INSPECT WIPER BLADES – INSPECT ENGINE OIL & FILTER – REPLACE – [If 0W-16 oil WAS NOT used at the last oil change, replace engine oil and oil filter. Reset the oil replacement reminder light ("MAINT REQD") or the message "OIL MAINTENANCE REQUIRED" on the multi-information display after maintenance at every 5,000 miles.] TIRES – ROTATE – [Check tire tread depth and for uneven or excessive wear.]
FRONT 35 REAR 35 (IN PSI UNIT) INSPECT TIRES AND ADJUST/INFLATE TIRE PRESSURE
BRAKE INSPECTION:FRONT (7 mm) REAR ( 6 mm) LINING REMAINING
PERFORM BATTERY TEST – PASSED
PERFORM MULTI INSPECTION
RESET REMINDER( ) REMINDER STICKER ( ) TEST DRIVE ( ) MILES
WHEEL LOCK (IF APPLICABLE) RESTORE ORIGINAL LOCATION.
TORQUE ALL LUG NUTS PER OEM SPEC (IF WHEELS REMOVED)
REPLACE CABIN AIR FILTER
EMILY C. gave our service a 5 star review on 3/5/2025
2015 Mercedes-Benz CLA250
Mileage
106,509
Service Date
3/3/2025
Services Performed
FOUND LOWER CONTROL ARM COVER BROKEN. REMOVE. ALSO REAR TIRES CUPPED.
FRONT 39 REAR 35 (IN PSI UNIT) INSPECT TIRES AND ADJUST/INFLATE TIRE PRESSURE
BRAKE INSPECTION:FRONT ( 7 mm) REAR ( 8 mm) LINING REMAINING
PERFORM BATTERY TEST – PASSED
PERFORM MULTI INSPECTION
TANNER G. gave our service a 5 star review on 3/4/2025
2015 Mercedes-Benz CLA250
Mileage
75,217
Service Date
2/19/2025
Services Performed
The first Service B is due at 20000 miles or 24 months, then every 20000 miles or 24 months. TIRE PRESSURE MONITORING SYSTEM SENSORS – ACTIVATE AXLE – INSPECT – [Check condition of front/rear axles and front/rear axle ball joints.] BRAKE FLUID – INSPECT – [In the event of fluid loss, determine cause and perform repair.] BRAKE SYSTEM – INSPECT – [Visually check condition of brake pads/linings, condition of brake disks.] COOLANT LEVEL – INSPECT – [Check coolant level in coolant expansion tank.] ENGINE COMPARTMENT – INSPECT – [Check all visible parts in the engine compartment for damage and leaks. In the event of fluid loss, determine cause and perform repair.] EXTERIOR LAMPS – INSPECT – [Check exterior lighting for correct function. Check and correct headlamp setting: Xenon or LED headlamps.] HORN OPERATION – INSPECT – [Check horn for correct function.] PARKING BRAKE – INSPECT – [Function test only: Vehicles with 4MATIC: If brake test is carried out on a dynamometer, the brake test may not exceed 10 seconds on each axle. You could otherwise damage the drive train or the brake system.] POLY-V-BELT – INSPECT – [Check poly-V-belt for wear in visible area.] STEERING SYSTEM – INSPECT – [Check condition of steering system and tie rods.] SUSPENSION SYSTEM – INSPECT – [Check condition of spring strut or shock absorber and spring.] TIRES – INSPECT – [Correct tire inflation pressure, Correct inflation pressure in spare tire (where applicable). Check TIREFIT sealant expiration date (where applicable). If expired, replace it. Activate Tire Pressure Monitoring System.] TRUNK LIGHTING – INSPECT – [Check trunk/cargo compartment lighting for correct function.] VEHICLE – INSPECT – [Check vehicle's exterior for damage in visible area. Check all visible components on the vehicle underside for leaks and damage: In the event of fluid loss, determine cause and perform repair. Country-specific regulations for mobility and body shell complaints apply.] WARNING & INDICATOR LAMPS – INSPECT – [Inspect warning and function indicator lamps in the instrument cluster. Check illumination of the instrument cluster and interior lighting for correct function.] WINDSHIELD WIPER & WASHER SYSTEMS – INSPECT – [Check windshield wipers, windshield for damage. Check and correct windshield washer system fluid level. Summer/winter washer fluid.] AIR FILTER – REPLACE – Activated Charcoal Filter ENGINE OIL – REPLACE ENGINE OIL FILTER – REPLACE SERVICE INTERVAL INDICATOR/DISPLAY – RESET – [Read out service data from instrument cluster and reset ASSYST PLUS service interval display. If the service/maintenance work has not, or has only partially been carried out after the ASSYST PLUS service interval display has been reset, the maintenance computer must be reset to its original settings.]
FOUND REAR RIGHT CALIPER SEIZED INSIDE PAD 0MM OUTSIDE 6MM. RECOMMEND REAR RIGHT CALIPER AND BRAKE SERVICE.
FRONT 39 REAR 39 (IN PSI UNIT) INSPECT TIRES AND ADJUST/INFLATE TIRE PRESSURE
BRAKE INSPECTION:FRONT (6 mm) REAR ( 6/0 mm) LINING REMAINING
PERFORM BATTERY TEST – PASSED
PERFORM MULTI INSPECTION
RESET REMINDER( ) REMINDER STICKER ( ) TEST DRIVE ( ) MILES
WHEEL LOCK (IF APPLICABLE) RESTORE ORIGINAL LOCATION.
TORQUE ALL LUG NUTS PER OEM SPEC (IF WHEELS REMOVED)
CALIPER – Remove & Replace – One Side,Front or Rear – [Includes: Bleed Brake System and replace Pads (if necessary).]
Remove and Replace Rear pads, Lube all Caliper Moving Mechanism. Check for Brake Hydraulic system and Brake Rotors. Test Drive
BRAKE ROTOR REPLACEMENT
Check brake fluid for moisture and contamination. Inspect all hydraulic line and hoses. Inspect calipers and wheel cylinders. Inspect master cylinder and cap. Flush entire brake system including master cylinder, calipers, wheel cylinders until clean.
CHRIS G. gave our service a 5 star review on 2/21/2025
2020 BMW 330i
Mileage
59,089
Service Date
2/7/2025
Services Performed
FRONT 35 REAR 41 (IN PSI UNIT) INSPECT TIRES AND ADJUST/INFLATE TIRE PRESSURE
BRAKE INSPECTION:FRONT ( 2 mm) REAR ( 0 mm) LINING REMAINING
PERFORM BATTERY TEST – PASSED
PERFORM MULTI INSPECTION
TEST DRIVE ( 4 ) MILES
WHEEL LOCK (IF APPLICABLE) RESTORE ORIGINAL LOCATION.
TORQUE ALL LUG NUTS PER OEM SPEC (IF WHEELS REMOVED)
Remove and Replace Rear pads, Lube all Caliper Moving Mechanism. Check for Brake Hydraulic system and Brake Rotors. Test Drive
BRAKE ROTOR REPLACEMENT
Remove and Replace Front pads, Lube all Caliper Moving Mechanism. Check for Front Brake Hydraulic system and Brake Rotors. Test Drive
BRAKE ROTOR REPLACEMENT
Check brake fluid for moisture and contamination. Inspect all hydraulic line and hoses. Inspect calipers and wheel cylinders. Inspect master cylinder and cap. Flush entire brake system including master cylinder, calipers, wheel cylinders until clean.
RESET ALL CONDITIONAL BASE FOR REPAIR.
LORRAINE P. gave our service a 5 star review on 2/9/2025
2008 Mazda 6
Mileage
151,603
Service Date
2/6/2025
Services Performed
FOUND WATER PUMP LEAKING AND SOAKING DRIVE BELT. RECOMMEND WATER PUMP AND WARRANTY DRIVE BELT.
Lubricate and check chassis Change oil and oil filter. Check wiper blades Check all fluid levels and tire pressures. Check belts and hoses Check Front brake and check steering Preform basic safety inspection. APPROVED: BMW LL01; MB-APP 229.5; VW 502.00/505.00
FRONT 35 REAR 35 (IN PSI UNIT) INSPECT TIRES AND ADJUST/INFLATE TIRE PRESSURE
BRAKE INSPECTION:FRONT ( 8 mm) REAR ( 8 mm) LINING REMAINING
PERFORM BATTERY TEST – PASSED. BATTERY HOLD DOWN BRACKET MISSING.
PERFORM MULTI INSPECTION
RESET REMINDER( ) REMINDER STICKER ( ) TEST DRIVE ( 12 ) MILES
WHEEL LOCK (IF APPLICABLE) RESTORE ORIGINAL LOCATION.
TORQUE ALL LUG NUTS PER OEM SPEC (IF WHEELS REMOVED)
WATER PUMP – Remove & Replace – In-Line4
COOLING SYSTEM BLEED – COMPLETE
Road test for power steering operation. Inspect system for leaks. Flush power steering lines, pump, rack and pinion, and or gear box. Install new power steering fluid. Road test vehicle.
SHOCK &/OR STRUT ASSEMBLY – Remove & Install or Remove & Replace – Both – [DOES NOT include disassemble or alignment.]
CONTROL ARM – Remove & Replace – In-Line4 Lower,Both,Front – [DOES NOT include alignment.]
CONTROL ARM – Remove & Replace – Both,Upper – [DOES NOT include alignment.]
STABILIZER BAR CONTROL LINK – Remove & Replace – Both – [DOES NOT include alignment.]
Road test vehicle. Check all suspension and steering parts for wear. Check tire pressure and condition. Check riding height. "CHECK" caster and camber, and (adjust toe in.) 3 month, 3000 mile warranty
AAA SHOP DISCOUNT
REMOVE AND REPLACE RIGHT FRONT TURN SIGNAL BULB.
ABEL H. gave our service a 5 star review on 2/8/2025
2013 Toyota RAV4
Mileage
66,444
Service Date
1/31/2025
Services Performed
ALSO REPLACE RELATED COMPONENET PART
SCAN ALL MODULES, PROVIDE REPORT AND RESET, AND PROVIDE SECOND REPORT ( )
TEST DRIVE FOR ADAS OPERATOIN ( ) MILES BY ( )
PRE-DELIVERY INSPECTION ( )
ROSE S. gave our service a 5 star review on 2/1/2025
2013 Toyota Camry
Mileage
50,913
Service Date
1/30/2025
Services Performed
DRIVER'S FLOOR MAT – CHECK – [Check installation of driver's floor mat. Only use the driver's floor mat designed specifically for the model and model year of the vehicle. Always properly secure the driver's floor mat using the retaining hooks. Never install another floor mat on top of the existing driver's floor mat. Never install the driver's floor mat upside down.] BRAKE SYSTEM – INSPECT – [Visually inspect brake linings/drums and brake pads/discs.] FLUID LEVELS – INSPECT – [Inspect and adjust all fluid levels.] ENGINE OIL & FILTER – REPLACE – [Reset the oil replacement reminder light ("MAINT REQD") or the message "OIL MAINTENANCE REQUIRED" on the multi-information display after maintenance at every 5,000 miles.] TIRES – ROTATE – [Check tire tread depth and for uneven or excessive wear.]
FRONT 35 REAR 35 (IN PSI UNIT) INSPECT TIRES AND ADJUST/INFLATE TIRE PRESSURE
BRAKE INSPECTION:FRONT ( 3 mm) REAR ( 5 mm) LINING REMAINING
PERFORM BATTERY TEST – PASSED
PERFORM MULTI INSPECTION
RESET REMINDER( ) REMINDER STICKER ( ) TEST DRIVE ( ) MILES
WHEEL LOCK (IF APPLICABLE) RESTORE ORIGINAL LOCATION.
TORQUE ALL LUG NUTS PER OEM SPEC (IF WHEELS REMOVED)
BALL JOINT – Remove & Replace – Gas Lower,Both – [DOES NOT include alignment.]
STABILIZER BAR CONTROL LINK – Remove & Replace – Both
Road test vehicle. Check all suspension and steering parts for wear. Check tire pressure and condition. Check riding height. "CHECK" caster and camber, and (adjust toe in.) 3 month, 3000 mile warranty
Check for minimum thickness and machine brake disk rotors, using on car brake lathe.
Remove and Replace Front pads, Lube all Caliper Moving Mechanism. Check for Front Brake Hydraulic system and Brake Rotors. Test Drive
Check brake fluid for moisture and contamination. Inspect all hydraulic line and hoses. Inspect calipers and wheel cylinders. Inspect master cylinder and cap. Flush entire brake system including master cylinder, calipers, wheel cylinders until clean.
KELLY M. gave our service a 5 star review on 1/31/2025
2018 Nissan Rogue Sport
Mileage
71,515
Service Date
1/28/2025
Services Performed
ALSO REPLACE RELATED COMPONENET PART
REMOVE RIGHT FRONT DOOR BELT MOLDING, OUTSIDE HANDLE, RIGHT SIDE MIRROR, LOWER BLACK MOLDING. REMOVE RIGHT REAR DOOR OUTSIDE HANDLE, BELT MOLDING, LOWER BLACK MOLDING.
SCAN ALL MODULES, PROVIDE REPORT AND RESET, AND PROVIDE SECOND REPORT ( )
TEST DRIVE FOR ADAS OPERATOIN ( ) MILES BY ( )
PRE-DELIVERY INSPECTION ( )
FRONT 35 REAR 35 (IN PSI UNIT) INSPECT TIRES AND ADJUST/INFLATE TIRE PRESSURE
BRAKE INSPECTION:FRONT ( 8 mm) REAR ( 4 mm) LINING REMAINING
PERFORM BATTERY TEST – MARGINAL. MONITOR.
PERFORM MULTI INSPECTION
LYNNE B. gave our service a 5 star review on 1/29/2025
2019 Hyundai Tucson
Mileage
70,049
Service Date
1/17/2025
Services Performed
ALSO REPLACE RELATED COMPONENET PART
REMOVE REAR BUMPER COVER. REMOVE LIFT GATE LOWER MOLDING. CHECK FOR ADDITIONAL DAMAGE.
SCAN ALL MODULES, PROVIDE REPORT AND RESET, AND PROVIDE SECOND REPORT ( )
TEST DRIVE FOR ADAS OPERATOIN ( ) MILES BY ( 10 )
PRE-DELIVERY INSPECTION ( )
FRONT 32 REAR 32 (IN PSI UNIT) INSPECT TIRES AND ADJUST/INFLATE TIRE PRESSURE
BRAKE INSPECTION:FRONT ( 3 mm) REAR ( 5 mm) LINING REMAINING
PERFORM BATTERY TEST – PASSED
PERFORM MULTI INSPECTION
WHEEL LOCK (IF APPLICABLE) RESTORE ORIGINAL LOCATION.
TORQUE ALL LUG NUTS PER OEM SPEC (IF WHEELS REMOVED)
SEUNG HWA L. gave our service a 5 star review on 1/18/2025

CRM Mitchell1

We Service and Repair all CRM Mitchell1 cars